English
100% Original Sfp 10gbase - 10GBASE-SR SFP+ 850nm 300m Hi-Optel HSFP10-3831 module – Hi-optel Featured Image
  • 100% Original Sfp 10gbase - 10GBASE-SR SFP+ 850nm 300m Hi-Optel HSFP10-3831 module – Hi-optel

100% Original Sfp 10gbase - 10GBASE-SR SFP+ 850nm 300m Hi-Optel HSFP10-3831 module – Hi-optel

Short Description:


Download as PDF

Product Detail

Product Tags

Related Video

Feedback (2)

We persist with the principle of "quality 1st, assistance initially, continual improvement and innovation to meet the customers" for your management and "zero defect, zero complaints" as the standard objective. To great our service, we present the products and solutions while using the very good top quality at the reasonable cost for Fibre Channel Transceiver , Sfp Fiber Transceiver , Coherent Optical Module , Should you be on the lookout forever Quality at a very good price tag and timely delivery. Do speak to us.
100% Original Sfp 10gbase - 10GBASE-SR SFP+ 850nm 300m Hi-Optel HSFP10-3831 module – Hi-optel Detail:

Descriptions

Fiber type Minimum modal bandwidth @ 850 nm (MHz●km) Operatingra nge (meters)
62.5um MMF 160 2 to 26
200 2 to 33
50um MMF 400 2 to 66
500 2 to 82
2000 2 to 300

SFP+SR Operating Range for each Optical Fiber Type

The transceiver consists of two sections: The high performance 850nm VCSEL transmitter and high sensitivity PIN integrated with a TIA. Receiver.

A block diagram of the HSFP10-3831 SFP+ optical transceiver is shown below

sr

● Absolute Maximum Ratings

Parameter Symbol Min Max Unit
Storage Temperature TST -40 +85  ℃
Supply Voltage VCC3 0 +3.6 V
Relative Humidity RH 5 85 %

● Recommend Operation Environment

Parameter Symbol Min Typ Max Unit
Date Rate 10.3125 Gb/s
Supply Voltage VCC +3.14 3.3 +3.47 V
Supply Current ICC 180 200 mA
Power Dissipation PD 0.8 W
Operating Temperature TOP -5 25 +75 ℃

● Transmitter Operating Characteristic-Optical, Electrical

Parameter Symbol Min Typ Max Unit Ref.
Side Mode Suppression Ratio SMSR 30 - dBm
Average launch power of OFF transmitter Poff - -30 dBm
Extinction Ratio ER 3.5 - dB 1
Transmitter Dispersion Penalty TDP - - 3.9 dB
Operating Data Rate S 10.3125 Gbps
Centre Wavelength λC 840 850 860 nm
Spectrum Band Width (RMS) σ 0.45 nm
Average Optical Power Pavg -7.3 - -1 dBm
Optical Eye Mask Compliant with IEEE 802.3ae
Input Differential Impedance ZIN 90 100 110 Ω
TX Disable Disable 2.0 Vcc+0.3 V
Enable 0 0.8 V
TX Fault Fault 2.0 Vcc+0.3 V
Normal 0 0.8 V
Data Dependent Input Jitter DDJ 0.08 UI
Data Input Total Jitter TJ 0.25 UI

● Receiver Operating Characteristic-Optical, Electrical

Parameter Symbol Min Typ Max Unit Ref.
Center Wavelength λr 850 nm
Average receiver power PIN -11.1 dBm 2
Receiver Overload PMAX -1.0 dBm 2
Los Assert LosA -30 - dBm
Los Dessert LosD -12 dBm
Los Hysteresis LosH 0.5 2.5 5 dB
Receiver Reflectance -12 dB 1
Output Differential Impedance PIN 90 100 110 Ω
LOS High 2.0 Vcc+0.3 V
Low 0 0.8
Rx Output Rise and Fall Time Tr/Tf 30 ps 20% to 80%
Total Output Jitter TJ 0.7 UI
Data Dependent Output Jitter DJ 0.42 UI

Notes:
Note 1. Measured at 10.3125b/s with PRBS 231 – 1 NRZ test pattern.
Note 2. Under the ER worst case, measured at 10.3125 Gb/s with PRBS 231 – 1 NRZ test pattern for BER

● Control and Status I/O Timing Characteristics

Parameter Symbol Min Max Unit Ref.
TX Disable Assert Time t_off 10 µs 1
TX Disable Negate Time t_on 1 ms 2
Time to initialize including reset of TX_Fault t_init 300 ms 3
TX Fault Assert Time t_fault 100 µs 4
TX Disable to reset t_reset 10 µs 5
LOS Assert Time t_loss_on 100 µs 6
LOS Deassert Time t_loss_off 100 µs 7
Rate-Select Change Time t_ratesel 10 µs 8
Serial ID Clock Rate f_serial_clock 400 kHz

Notes:
1. Time from rising edge of TX Disable to when the optical output falls below 10% of nominal.
2. Time from falling edge of TX Disable to when the modulated optical output rises above 90% of nominal.
3. From power on or negation of TX Fault using TX Disable.
4. Time from fault to TX fault on.
5. Time TX Disable must be held high to reset TX_fault.
6. Time from LOS state to RX LOS assert.
7. Time from non-LOS state to RX LOS deassert.
8. Time from rising or falling edge of Rate Select input until receiver bandwidth is in conformance with appropriate specification.

Regulatory Compliance

The HSFP10-383X complies with international Electromagnetic Compatibility and international safety requirements and standards (see details in Table following).

Electrostatic Discharge
(ESD) to the Electrical Pins		 MIL-STD-883E
Method 3015.4		 Class 1(>2000 V)
Electromagnetic
Interference (EMI)		 FCC Part 15 Class B
EN55022 Class B (CISPR 22B)
VCCI Class B		 Compatible with standards
Laser Eye Safety FDA 21CFR 1040.10 and 1040.11
EN60950, EN (IEC) 60825-1,2		 Compatible with Class 1 laser product.
Product detail pictures:

100% Original Sfp 10gbase - 10GBASE-SR SFP+ 850nm 300m Hi-Optel HSFP10-3831 module – Hi-optel detail pictures

Related Product Guide:
Sticking to the principle of "Super High-quality, Satisfactory service" ,We are striving to generally be a very good business partner of you for 100% Original Sfp 10gbase - 10GBASE-SR SFP+ 850nm 300m Hi-Optel HSFP10-3831 module – Hi-optel , The product will supply to all over the world, such as: Pakistan, Swiss, Swedish, The quality of our merchandise is equal to OEM's quality, because our core parts are the same with OEM supplier. The above items have passed professional certification, and we not only can produce OEM-standard items but we also accept Customized Merchandise order.
    • In China, we have many partners, this company is the most satisfying to us, reliable quality and good credit, it is worth appreciation.
    5 Stars By Charlotte from Pretoria - 2018.12.22 12:52
    The manufacturer gave us a big discount under the premise of ensuring the quality of products, thank you very much, we will select this company again.
    5 Stars By jari dedenroth from France - 2018.12.11 11:26
    Write your message here and send it to us

    Products categories

    Hit enter to search or ESC to close