Top Suppliers Sfp+ 10g Bidi - 10GBASE-SR SFP+ 850nm 300m Hi-Optel HSFP10-3831 module – Hi-optel
Top Suppliers Sfp+ 10g Bidi - 10GBASE-SR SFP+ 850nm 300m Hi-Optel HSFP10-3831 module – Hi-optel Detail:
Descriptions
| Fiber type | Minimum modal bandwidth @ 850 nm (MHz●km) | Operatingra nge (meters) |
| 62.5um MMF | 160 | 2 to 26 |
| 200 | 2 to 33 | |
| 50um MMF | 400 | 2 to 66 |
| 500 | 2 to 82 | |
| 2000 | 2 to 300 |
SFP+SR Operating Range for each Optical Fiber Type
The transceiver consists of two sections: The high performance 850nm VCSEL transmitter and high sensitivity PIN integrated with a TIA. Receiver.
A block diagram of the HSFP10-3831 SFP+ optical transceiver is shown below
● Absolute Maximum Ratings
| Parameter | Symbol | Min | Max | Unit |
| Storage Temperature | TST | -40 | +85 | ℃ |
| Supply Voltage | VCC3 | 0 | +3.6 | V |
| Relative Humidity | RH | 5 | 85 | % |
● Recommend Operation Environment
| Parameter | Symbol | Min | Typ | Max | Unit |
| Date Rate | 10.3125 | Gb/s | |||
| Supply Voltage | VCC | +3.14 | 3.3 | +3.47 | V |
| Supply Current | ICC | 180 | 200 | mA | |
| Power Dissipation | PD | 0.8 | W | ||
| Operating Temperature | TOP | -5 | 25 | +75 | ℃ |
● Transmitter Operating Characteristic-Optical, Electrical
| Parameter | Symbol | Min | Typ | Max | Unit | Ref. | |
| Side Mode Suppression Ratio | SMSR | 30 | - | dBm | |||
| Average launch power of OFF transmitter | Poff | - | -30 | dBm | |||
| Extinction Ratio | ER | 3.5 | - | dB | 1 | ||
| Transmitter Dispersion Penalty | TDP | - | - | 3.9 | dB | ||
| Operating Data Rate | S | 10.3125 | Gbps | ||||
| Centre Wavelength | λC | 840 | 850 | 860 | nm | ||
| Spectrum Band Width (RMS) | σ | 0.45 | nm | ||||
| Average Optical Power | Pavg | -7.3 | - | -1 | dBm | ||
| Optical Eye Mask | Compliant with IEEE 802.3ae | ||||||
| Input Differential Impedance | ZIN | 90 | 100 | 110 | Ω | ||
| TX Disable | Disable | 2.0 | Vcc+0.3 | V | |||
| Enable | 0 | 0.8 | V | ||||
| TX Fault | Fault | 2.0 | Vcc+0.3 | V | |||
| Normal | 0 | 0.8 | V | ||||
| Data Dependent Input Jitter | DDJ | 0.08 | UI | ||||
| Data Input Total Jitter | TJ | 0.25 | UI | ||||
● Receiver Operating Characteristic-Optical, Electrical
| Parameter | Symbol | Min | Typ | Max | Unit | Ref. | |
| Center Wavelength | λr | 850 | nm | ||||
| Average receiver power | PIN | -11.1 | dBm | 2 | |||
| Receiver Overload | PMAX | -1.0 | dBm | 2 | |||
| Los Assert | LosA | -30 | - | dBm | |||
| Los Dessert | LosD | -12 | dBm | ||||
| Los Hysteresis | LosH | 0.5 | 2.5 | 5 | dB | ||
| Receiver Reflectance | -12 | dB | 1 | ||||
| Output Differential Impedance | PIN | 90 | 100 | 110 | Ω | ||
| LOS | High | 2.0 | Vcc+0.3 | V | |||
| Low | 0 | 0.8 | |||||
| Rx Output Rise and Fall Time | Tr/Tf | 30 | ps | 20% to 80% | |||
| Total Output Jitter | TJ | 0.7 | UI | ||||
| Data Dependent Output Jitter | DJ | 0.42 | UI | ||||
Notes:
Note 1. Measured at 10.3125b/s with PRBS 231 – 1 NRZ test pattern.
Note 2. Under the ER worst case, measured at 10.3125 Gb/s with PRBS 231 – 1 NRZ test pattern for BER
● Control and Status I/O Timing Characteristics
| Parameter | Symbol | Min | Max | Unit | Ref. |
| TX Disable Assert Time | t_off | 10 | µs | 1 | |
| TX Disable Negate Time | t_on | 1 | ms | 2 | |
| Time to initialize including reset of TX_Fault | t_init | 300 | ms | 3 | |
| TX Fault Assert Time | t_fault | 100 | µs | 4 | |
| TX Disable to reset | t_reset | 10 | µs | 5 | |
| LOS Assert Time | t_loss_on | 100 | µs | 6 | |
| LOS Deassert Time | t_loss_off | 100 | µs | 7 | |
| Rate-Select Change Time | t_ratesel | 10 | µs | 8 | |
| Serial ID Clock Rate | f_serial_clock | 400 | kHz |
Notes:
1. Time from rising edge of TX Disable to when the optical output falls below 10% of nominal.
2. Time from falling edge of TX Disable to when the modulated optical output rises above 90% of nominal.
3. From power on or negation of TX Fault using TX Disable.
4. Time from fault to TX fault on.
5. Time TX Disable must be held high to reset TX_fault.
6. Time from LOS state to RX LOS assert.
7. Time from non-LOS state to RX LOS deassert.
8. Time from rising or falling edge of Rate Select input until receiver bandwidth is in conformance with appropriate specification.
Regulatory Compliance
The HSFP10-383X complies with international Electromagnetic Compatibility and international safety requirements and standards (see details in Table following).
| Electrostatic Discharge (ESD) to the Electrical Pins |
MIL-STD-883E Method 3015.4 |
Class 1(>2000 V) |
| Electromagnetic Interference (EMI) |
FCC Part 15 Class B EN55022 Class B (CISPR 22B) VCCI Class B |
Compatible with standards |
| Laser Eye Safety | FDA 21CFR 1040.10 and 1040.11 EN60950, EN (IEC) 60825-1,2 |
Compatible with Class 1 laser product. |
Product detail pictures:
Related Product Guide:
"Quality to start with, Honesty as base, Sincere company and mutual profit" is our idea, as a way to build constantly and pursue the excellence for Top Suppliers Sfp+ 10g Bidi - 10GBASE-SR SFP+ 850nm 300m Hi-Optel HSFP10-3831 module – Hi-optel , The product will supply to all over the world, such as: Burundi, Pakistan, Toronto, Many products fully conform to the most rigorous of international guidelines and with our first-rate delivery service you will have them delivered at any time and in any place. And because Kayo deals in the entire spectrum of protective equipment, our customers don't need to waste time shopping around.
By Freda from Saudi Arabia - 2017.06.16 18:23
The customer service staff's answer is very meticulous, the most important is that the product quality is very good, and packaged carefully, shipped quickly!
By Daisy from Palestine - 2018.12.22 12:52
